Saudações
Exercício 01
Bem vindo ao exercício número 01, que inicia a aeronave para vôo, com checagem dos instrumentos e ativação de todo sistema elétrico, motores, sistemas hidráulicos e radio frequência.
Missão de iniciar uma aeronave em ramp start
Primeiro passo:(entrando na realidade) Visualizar quaisquer anomalias na fuzelagem, trem de pouso, entrada e saída da turbina, botões externos, tampas externas "se bem fechadas", flaps, Asas, aileron,retirar "travas de rodas", retirar "avisos nos instrumentos externos" . Ao entrar na aeronave, checar visualmente se não há danos superficiais nos controles e botões, checar sinto de segurança e fivelas (ajusta-los), observar o canopy e qualquer alteração no ambiente do cockipit do piloto.
Checar se todos os instrumentos estão desligados.
Procedimento INICIAL:
1. MAIN PWR - BATERIA "BATT"-CHECK LUZ DE AVISO"ATIVAR"
2. MAIN PWR - Flcs RELAY "ON"
3. MAIN PWR - POSIÇÃO "MAIN" CHECK LUZ
4. Parking Brake - ATIVE
5. Master LIGHT switch - "NORM"
6. LUZ DE ANTI-COLISÃO - ATIVE POSIÇÃO "ON"
7. LUZ FLASH - ATIVE POSIÇÃO "FLASH"
7. Master FUEL Switch - ATIVE PARA "NORM"
8. FUEL Pumps - ATIVE PARA "NORM"
9. Fuel Readout Switch - ATIVE PARA "NORM"
10.EPU Switch - ATIVE PARA "NORM"
11.AIR Source - ATIVE PARA "NORM"
12.Avionics - DESATIVADOS
13.Sensors - DESATIVADOS
14.SEAT - ASSENTO "ARMADO"
15.WARNING PAINEL - "ELECSYS ON" "SEC ON" "HYD OIL ON"
16.EPU – “OFF” DESLIGADA
17.RADIOS E INTERCON “LIGADOS” COM VOLUME CONFORME AJUSTE NECESSÁRIO
PROCEDIMENTO PARA INICIAR O(S) MOTORE(S)
1. Throttle - PISIÇÃO “0” IDLE -ACELERAÇÃO MÍNIMA
2. JFS /APU– ATIVE POSIÇÃO 02
3. RPM (INSTRUMENTO) – INICIA PROCESSO ATÉ 25%
4. Throttle - AUMENTAR ACELERAÇÃO ACIMA DE 30%
5. Idle Detent – ATIVE O BOTÃO IDLE DETENT
6. RPM (INSTRUMENTO) – AUMENTO DE ROTAÇÃO ACIMA 25%
7. Throttle – POSIÇÃO “0” IDLE- ACELERAÇÃO MÍNIMA
8. 50% RPM – INTERRUPTOR (JFS) POSIÇÃO “OFF”
9. 55% RPM – BATERIA (MAIN GEN) LUZ DESLIGADA “OFF”
10.HYD OIL light–AVISO PAINEL LUZ DESLIGADA “OFF” APÓS 70% RPM
CHECK. luzes de painel de avisos
APÓS INICIAR MOTORES
1. D/Link - ATIVAR
2. GPS – ATIVAR
3. UFC / ded – ATIVAR
4. MFD - ATIVAR
5. SMS - ATIVAR
6. FCC – ATIVAR
7. INS – POSIÇÃO “ALGIN NORM” – DADOS E COORDENADAS
8. FCR - ATIVAR
9. Left/Right Hardpoints – ASAS -ATIVAR
10.RALT – ATIVAR POSIÇÃO “STAND-BY”
11.HUD – ATIVAR
11.HUD – MODIFICAR BRILHO CONFORME CONFIGURAÇÃO PESSOAL
12.Trim – ZERAR “RESET”
CHECK. luzes de painel de avisos
MOTOR CHECK
1. FLUEL FLOW - 500 – 1500 RPM
2. RPM - 60 – 70 %
3. FTIT (INSTRUMENTO) – INFERIOR A 575°
4. Hyd Oil – LUZ DE AVISO DESLIGADA
5. Engine Gauges - AVISO VERDE
FLUEL CHECK
1. TOTALIZER QTY – CHECK DE ACORDO COM O PLANO DE VÔO
2. NORM – A/L 32000 LBS – F/R 37000LBS
3. TEST – TOT: 6000 LBS A/L – F/R: 2000 LBS
4. RSVR – BOTH 480 LBS – MARQUE SISTEMA DED CONFORME PLANO DE VÔO
5. INT WING – BOTH 500 LBS
6. EXT WING – BOTH 2420 LBS (TANQUES EXTERNOS)
7. EXT CTL – F/R: 1700 LBS - CHECK 95 -102%
AVIONICS
1. Threat Warning Aux - ATIVAR
2. EWMS *
EWS PWR - ATIVAR
EWS JMR - ATIVAR
Chaff CMDs – ATIVAR
Flares CMDs - ATIVAR
EWMS Mode – SELEÇÃO REQUERIDA
3. Check CNI switch – CHECK “UFC”
4. DED – UFC *
Comms – SELECIONAR UHF E VHF
ALOW – SELEÇÃO REQUERIDA
MSL (trans alt) – SELEÇÃO REQUERIDA
CRUS – SELEÇÃO “HOME” BASE ALPHA
TACAN – SELEÇÃO PARA BASE ALPHA “HOME”
BINGO – SELEÇÃO REQUERIDA
VIP – VRP – SELEÇÃO REQUERIDA
WSPAN – SELECIONAR E CHECAR
5. MFD *
S – Jettison – ATIVO SELECIONADO
Flightplan – CHECK E SELECIONE
6. AUDIO *
COMM1 Volume - SELECIONAR
COMM2 Volume - SELECIONAR
MSL Threat Volume - SELECIONAR
Threat Volume - SELECIONAR
Repetir procedimento sem fechar canopy e pressurizar cabine
Radio ADF Navigation
VHF Radios
Front dash, navigation mode select panel ILS and TCN buttons Disengage
Left console, VHF radio head Mode Selector knob Set to DF
Left console, VHF radio head Frequency switches Set ADF frequency
Font dash, navigation mode select panel VHF Light Confirm lit
Front dash ADI Steer towards Bank Steering bar and monitor Pitch Steering Bar regarding ADF signal strength
UHF Radio
Left console, UHF radio head Function Select switch Set to ADF
Left console, UHF radio Frequency switches Set ADF
head frequency
Font dash, navigation mode select panel UHF Light Confirm lit
Front dash HSI Follow Bearing Pointer 1 steering
Waypoint Selection
Right console, AAP panel PAGE dial Set to WAYPT
Right console, Waypoint Page Enter name of
CDU Waypoint in scratchpad and press top right line select key.
Right console, CDU Waypoint Page Enter ID number of Waypoint in scratchpad and press top left line select key.
Embedded GPS INS (EGI) Navigation Panel Controls Operation
Creating New Waypoint
Right console, AAP panel PAGE dial Set to WAYPT
Right console, CDU PAGE display Select Waypoint branch
Right console, CDU Waypoint Info page Select Copy (?xx) function to create new Mission waypoint
Right console, CDU Waypoint Info page Enter elevation of new waypoint in scratchpad and press EL line select key
Right console, CDU Waypoint Info page Enter latitude of new waypoint in scratchpad and press N/S line select key
Right console, CDU Waypoint Info page Enter longitude of new waypoint in scratchpad and press E/W line select key
Right console, CDU Waypoint Info page Enter unique name of new waypoint in scratchpad and press name field line select key
Set Steerpoint
Right console, AAP panel PAGE dial Set to STEER
Right console, CDU Steerpoint Info page Cycle with ± rocker on CDU
HUD HUD as SOI DMS Up and Down
Set Anchor Point
Right console, AAP panel PAGE dial Set to WAYPT
Right console, CDU PAGE display Select Anchor Pt branch
Right console, CDU Anchor Point Info page Enter name of Waypoint in scratchpad and press top right line select key.
Right console, CDU Anchor Point Info page Enter ID number of Waypoint in scratchpad and press top left line select key.
Mark Creation and Cycling
Right console, CDU MK (Mark Point) button Press to create overhead Mark Point
TDC, TAD Cursor, TGP, and Maverick Designation point TMS Right Short to set Mark Point
Right console, AAP panel STEER PT dial Set to MARK
Right console, CDU ± Rocker switch Press to cycle Mark Points
HUD HUD as SOI DMS Up and Down to cycle Mark Points
Create Flight Plan
Right console, AAP panel PAGE dial Set to OTHER
Right console, AAP panel STEER PT dial Set to FLT PLAN
Right console, CDU FPM Function Select Key Press
Right console, CDU FPM Info Page Enter name of new FP in scratchpad and press NEW FP line select key
Right console, CDU FPM Info Page Press line select key of new flight plan
Right console, CDU FPM Info Page Press FPBUILD line select key
Right console, CDU Flight Plan Build page Enter waypoint number of waypoint to be added to plan in scratchpad and press line select key of flight plan slot
Right console, CDU Flight Plan Build page Repeat to add all waypoints of new flight plan
PAINEL DE CONTRA-MEDIDAS ELETRÔNICAS - GUERRA ELETRÔNICA
Mode Select - dial Set to STBY
DISP switch -Set to MENU
CHAFF, FLAR, INTV, or CYCL SET button Press to enter value
Next (NXT) rocker switch Press to adjust value
Return (RTN) button Save data
DISP switch Set to ON
RWR switch Set to ON
JMR switch Set to ON
MWS switch Set to ON
SELEÇÃO DE ARMAS
Master Arm switch Set to OFF
GUN/PAC switch Set to OFF
LASER switch Set to OFF
DSMS Status page
Review store loading and resolve errors
CONFIGURAÇÃO DE ARMAS
DSMS Profile page MDF - Select desired profile using OBS 19 and 20
DSMS Profile page Set selected profile as active by pressing ACT PRO OSB 17
DSMS Profile Control page Set release control as desired. Enter value in scratchpad and press OSB next to setting
DSMS Settings page Set release settings as desired. Enter value in scratchpad and press OSB next to setting
Manual Profile Select
Front dash, MFCD DSMS Status page Press OSB next to weapon station
HUD Rotary Profile Select
HUD HUD as SOI Press DMS Left and Right to cycle through profiles on HUD rotary
WEAPON DELIVERY
CCIP Consent to Release (CR) Mode
IFFCC switch Set to TEST
IFFCC Test Menu Set CR option to 5 MIL or 3/9
IFFCC switch Set to ON
Master Arm switch Set to ARM
MFCD DSMS OSB Press
DSMS Status page Press PROF OSB 1
DSMS Profile Main page Press OSB 19 and 20 to select profile
DSMS Profile Main page Press ACT PRO OSB 17
DSMS Profile Main page Press VIEW PRO OSB 3
DSMS Profile Control page Set release settings
DSMS Profile Control page Press CHG SET OSB 16
DSMS Settings page Set release settings
Master Mode Select Button Cycle to CCIP
HUD symbology Align reticle over target and press and hold weapon release button
HUD symbology Maneuver aircraft such that solution cue passes through pipper
Laser-Guided Bomb
TGP switch Set to ON
LASER switch Set to ARM
MFCD TGP OSB Press
TGP STBY page Press A-G OSB 2 or A-A OSB 3 for Ground or Air modes
Slew switch Slew TGP line of
throttle sight over target
Control stick TMS Forward Long Set as SPI Press TMS Forward Long
Front dash, AHCP Master Arm switch Set to ARM
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Front dash, MFCD DSMS Profile Main page Press VIEW PRO OSB 3
Front dash, MFCD DSMS Profile Control page Set release settings
Front dash, MFCD DSMS Profile Control page Press CHG SET OSB 16
Front dash, MFCD DSMS Settings page Set release settings
Control stick Master Mode Select Button Cycle to CCRP Press Master Mode Select Button
HUD HUD symbology Align reticle over ASL and hold weapon release button down. Press Weapon Release Button
Control stick Laser fire switch Turn on Laser after bomb is released Press Nosewheel Steering Button
Front dash, MFCD TGP Maintain TGP line of sight to target during bomb time of flight
IAM-Guided Bomb
Designation device Set SPI using steerpoint, TDC,
TGP, TAD or Maverick (TMS Forward Long)
Left console, AHCP Master Arm switch Set to ARM
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Control stick Master Mode Select Button Cycle to CCRP Press Master Mode Select Button
HUD HUD symbology Align reticle over ASL and hold weapon release button down. Press Weapon Release Button
Control stick HUD symbology Bomb will release when release cue is between max and min range carets on reticle.
Maverick
Left console, AHCP Master Arm switch Set to ARM
Front dash, MFCD MAV OSB Press
Front dash, MFCD MAV page Power ON Maverick, press OSB 6. 3 minute alignment
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Control stick Master Mode Select Button Cycle to CCIP Press Master Mode Select Button
HUD HUD and MAV page Slew tracking gate over target and release slew to initiate tracking Move Slew Switch
Control stick Weapon release button Press with target lock indicated by steady Pointing Cross Press Weapon release button
Gun
Left console, AHCP Master Arm switch Set to ARM
Left console, AHCP GUN/PAC switch Set to ARM
Control stick Master Mode Select Button Set mode to GUNS Press Master Mode Select Button
Left console, throttle Coolie Hat up Set HUD as SOI Press Coolie Hat Up
Control stick DMS Left or Right Short Select gunsight Press DMS Left or Right
Control stick Trigger First stage enables PAC, second stage fires gun
Rockets
Left console, AHCP Master Arm switch Set to ARM
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Front dash, MFCD DSMS Profile Main page Press VIEW PRO OSB 3
Front dash, MFCD DSMS Profile Control page Set release settings
Front dash, MFCD DSMS Profile Control page Press CHG SET OSB 16
Front dash, MFCD DSMS Settings page Set release settings
Control stick Master Mode Select Button Cycle to CCIP or CCRP Press Master Mode Select Button
HUD HUD symbology CCIP: align CCIP pipper over target and press and hold weapon release button.
CCRP: Align reticle over ASL and hold weapon release button down. Press Weapon Release Button
Exercício 01
Bem vindo ao exercício número 01, que inicia a aeronave para vôo, com checagem dos instrumentos e ativação de todo sistema elétrico, motores, sistemas hidráulicos e radio frequência.
Missão de iniciar uma aeronave em ramp start
Iniciar da rampa para este exercício, lembrando que a sequência deve ser seguida para ativação dos componentes elétricos/hidráulicos da aeronave, pois não queremos danificar componentes essenciais e nem mesmo inciar um incêndio causando uma explosão letal para o piloto e pessoas/aeronaves próximas.
Primeiro passo:(entrando na realidade) Visualizar quaisquer anomalias na fuzelagem, trem de pouso, entrada e saída da turbina, botões externos, tampas externas "se bem fechadas", flaps, Asas, aileron,retirar "travas de rodas", retirar "avisos nos instrumentos externos" . Ao entrar na aeronave, checar visualmente se não há danos superficiais nos controles e botões, checar sinto de segurança e fivelas (ajusta-los), observar o canopy e qualquer alteração no ambiente do cockipit do piloto.
Checar se todos os instrumentos estão desligados.
Procedimento INICIAL:
1. MAIN PWR - BATERIA "BATT"-CHECK LUZ DE AVISO"ATIVAR"
2. MAIN PWR - Flcs RELAY "ON"
3. MAIN PWR - POSIÇÃO "MAIN" CHECK LUZ
4. Parking Brake - ATIVE
5. Master LIGHT switch - "NORM"
6. LUZ DE ANTI-COLISÃO - ATIVE POSIÇÃO "ON"
7. LUZ FLASH - ATIVE POSIÇÃO "FLASH"
7. Master FUEL Switch - ATIVE PARA "NORM"
8. FUEL Pumps - ATIVE PARA "NORM"
9. Fuel Readout Switch - ATIVE PARA "NORM"
10.EPU Switch - ATIVE PARA "NORM"
11.AIR Source - ATIVE PARA "NORM"
12.Avionics - DESATIVADOS
13.Sensors - DESATIVADOS
14.SEAT - ASSENTO "ARMADO"
15.WARNING PAINEL - "ELECSYS ON" "SEC ON" "HYD OIL ON"
16.EPU – “OFF” DESLIGADA
17.RADIOS E INTERCON “LIGADOS” COM VOLUME CONFORME AJUSTE NECESSÁRIO
PROCEDIMENTO PARA INICIAR O(S) MOTORE(S)
1. Throttle - PISIÇÃO “0” IDLE -ACELERAÇÃO MÍNIMA
2. JFS /APU– ATIVE POSIÇÃO 02
3. RPM (INSTRUMENTO) – INICIA PROCESSO ATÉ 25%
4. Throttle - AUMENTAR ACELERAÇÃO ACIMA DE 30%
5. Idle Detent – ATIVE O BOTÃO IDLE DETENT
6. RPM (INSTRUMENTO) – AUMENTO DE ROTAÇÃO ACIMA 25%
7. Throttle – POSIÇÃO “0” IDLE- ACELERAÇÃO MÍNIMA
8. 50% RPM – INTERRUPTOR (JFS) POSIÇÃO “OFF”
9. 55% RPM – BATERIA (MAIN GEN) LUZ DESLIGADA “OFF”
10.HYD OIL light–AVISO PAINEL LUZ DESLIGADA “OFF” APÓS 70% RPM
CHECK. luzes de painel de avisos
APÓS INICIAR MOTORES
1. D/Link - ATIVAR
2. GPS – ATIVAR
3. UFC / ded – ATIVAR
4. MFD - ATIVAR
5. SMS - ATIVAR
6. FCC – ATIVAR
7. INS – POSIÇÃO “ALGIN NORM” – DADOS E COORDENADAS
8. FCR - ATIVAR
9. Left/Right Hardpoints – ASAS -ATIVAR
10.RALT – ATIVAR POSIÇÃO “STAND-BY”
11.HUD – ATIVAR
11.HUD – MODIFICAR BRILHO CONFORME CONFIGURAÇÃO PESSOAL
12.Trim – ZERAR “RESET”
CHECK. luzes de painel de avisos
MOTOR CHECK
1. FLUEL FLOW - 500 – 1500 RPM
2. RPM - 60 – 70 %
3. FTIT (INSTRUMENTO) – INFERIOR A 575°
4. Hyd Oil – LUZ DE AVISO DESLIGADA
5. Engine Gauges - AVISO VERDE
FLUEL CHECK
1. TOTALIZER QTY – CHECK DE ACORDO COM O PLANO DE VÔO
2. NORM – A/L 32000 LBS – F/R 37000LBS
3. TEST – TOT: 6000 LBS A/L – F/R: 2000 LBS
4. RSVR – BOTH 480 LBS – MARQUE SISTEMA DED CONFORME PLANO DE VÔO
5. INT WING – BOTH 500 LBS
6. EXT WING – BOTH 2420 LBS (TANQUES EXTERNOS)
7. EXT CTL – F/R: 1700 LBS - CHECK 95 -102%
AVIONICS
1. Threat Warning Aux - ATIVAR
2. EWMS *
EWS PWR - ATIVAR
EWS JMR - ATIVAR
Chaff CMDs – ATIVAR
Flares CMDs - ATIVAR
EWMS Mode – SELEÇÃO REQUERIDA
3. Check CNI switch – CHECK “UFC”
4. DED – UFC *
Comms – SELECIONAR UHF E VHF
ALOW – SELEÇÃO REQUERIDA
MSL (trans alt) – SELEÇÃO REQUERIDA
CRUS – SELEÇÃO “HOME” BASE ALPHA
TACAN – SELEÇÃO PARA BASE ALPHA “HOME”
BINGO – SELEÇÃO REQUERIDA
VIP – VRP – SELEÇÃO REQUERIDA
WSPAN – SELECIONAR E CHECAR
5. MFD *
S – Jettison – ATIVO SELECIONADO
Flightplan – CHECK E SELECIONE
6. AUDIO *
COMM1 Volume - SELECIONAR
COMM2 Volume - SELECIONAR
MSL Threat Volume - SELECIONAR
Threat Volume - SELECIONAR
Repetir procedimento sem fechar canopy e pressurizar cabine
Radio ADF Navigation
VHF Radios
Front dash, navigation mode select panel ILS and TCN buttons Disengage
Left console, VHF radio head Mode Selector knob Set to DF
Left console, VHF radio head Frequency switches Set ADF frequency
Font dash, navigation mode select panel VHF Light Confirm lit
Front dash ADI Steer towards Bank Steering bar and monitor Pitch Steering Bar regarding ADF signal strength
UHF Radio
Left console, UHF radio head Function Select switch Set to ADF
Left console, UHF radio Frequency switches Set ADF
head frequency
Font dash, navigation mode select panel UHF Light Confirm lit
Front dash HSI Follow Bearing Pointer 1 steering
Waypoint Selection
Right console, AAP panel PAGE dial Set to WAYPT
Right console, Waypoint Page Enter name of
CDU Waypoint in scratchpad and press top right line select key.
Right console, CDU Waypoint Page Enter ID number of Waypoint in scratchpad and press top left line select key.
Embedded GPS INS (EGI) Navigation Panel Controls Operation
Creating New Waypoint
Right console, AAP panel PAGE dial Set to WAYPT
Right console, CDU PAGE display Select Waypoint branch
Right console, CDU Waypoint Info page Select Copy (?xx) function to create new Mission waypoint
Right console, CDU Waypoint Info page Enter elevation of new waypoint in scratchpad and press EL line select key
Right console, CDU Waypoint Info page Enter latitude of new waypoint in scratchpad and press N/S line select key
Right console, CDU Waypoint Info page Enter longitude of new waypoint in scratchpad and press E/W line select key
Right console, CDU Waypoint Info page Enter unique name of new waypoint in scratchpad and press name field line select key
Set Steerpoint
Right console, AAP panel PAGE dial Set to STEER
Right console, CDU Steerpoint Info page Cycle with ± rocker on CDU
HUD HUD as SOI DMS Up and Down
Set Anchor Point
Right console, AAP panel PAGE dial Set to WAYPT
Right console, CDU PAGE display Select Anchor Pt branch
Right console, CDU Anchor Point Info page Enter name of Waypoint in scratchpad and press top right line select key.
Right console, CDU Anchor Point Info page Enter ID number of Waypoint in scratchpad and press top left line select key.
Mark Creation and Cycling
Right console, CDU MK (Mark Point) button Press to create overhead Mark Point
TDC, TAD Cursor, TGP, and Maverick Designation point TMS Right Short to set Mark Point
Right console, AAP panel STEER PT dial Set to MARK
Right console, CDU ± Rocker switch Press to cycle Mark Points
HUD HUD as SOI DMS Up and Down to cycle Mark Points
Create Flight Plan
Right console, AAP panel PAGE dial Set to OTHER
Right console, AAP panel STEER PT dial Set to FLT PLAN
Right console, CDU FPM Function Select Key Press
Right console, CDU FPM Info Page Enter name of new FP in scratchpad and press NEW FP line select key
Right console, CDU FPM Info Page Press line select key of new flight plan
Right console, CDU FPM Info Page Press FPBUILD line select key
Right console, CDU Flight Plan Build page Enter waypoint number of waypoint to be added to plan in scratchpad and press line select key of flight plan slot
Right console, CDU Flight Plan Build page Repeat to add all waypoints of new flight plan
PAINEL DE CONTRA-MEDIDAS ELETRÔNICAS - GUERRA ELETRÔNICA
Mode Select - dial Set to STBY
DISP switch -Set to MENU
CHAFF, FLAR, INTV, or CYCL SET button Press to enter value
Next (NXT) rocker switch Press to adjust value
Return (RTN) button Save data
DISP switch Set to ON
RWR switch Set to ON
JMR switch Set to ON
MWS switch Set to ON
SELEÇÃO DE ARMAS
Master Arm switch Set to OFF
GUN/PAC switch Set to OFF
LASER switch Set to OFF
DSMS Status page
Review store loading and resolve errors
CONFIGURAÇÃO DE ARMAS
DSMS Profile page MDF - Select desired profile using OBS 19 and 20
DSMS Profile page Set selected profile as active by pressing ACT PRO OSB 17
DSMS Profile Control page Set release control as desired. Enter value in scratchpad and press OSB next to setting
DSMS Settings page Set release settings as desired. Enter value in scratchpad and press OSB next to setting
Manual Profile Select
Front dash, MFCD DSMS Status page Press OSB next to weapon station
HUD Rotary Profile Select
HUD HUD as SOI Press DMS Left and Right to cycle through profiles on HUD rotary
WEAPON DELIVERY
CCIP Consent to Release (CR) Mode
IFFCC switch Set to TEST
IFFCC Test Menu Set CR option to 5 MIL or 3/9
IFFCC switch Set to ON
Master Arm switch Set to ARM
MFCD DSMS OSB Press
DSMS Status page Press PROF OSB 1
DSMS Profile Main page Press OSB 19 and 20 to select profile
DSMS Profile Main page Press ACT PRO OSB 17
DSMS Profile Main page Press VIEW PRO OSB 3
DSMS Profile Control page Set release settings
DSMS Profile Control page Press CHG SET OSB 16
DSMS Settings page Set release settings
Master Mode Select Button Cycle to CCIP
HUD symbology Align reticle over target and press and hold weapon release button
HUD symbology Maneuver aircraft such that solution cue passes through pipper
Laser-Guided Bomb
TGP switch Set to ON
LASER switch Set to ARM
MFCD TGP OSB Press
TGP STBY page Press A-G OSB 2 or A-A OSB 3 for Ground or Air modes
Slew switch Slew TGP line of
throttle sight over target
Control stick TMS Forward Long Set as SPI Press TMS Forward Long
Front dash, AHCP Master Arm switch Set to ARM
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Front dash, MFCD DSMS Profile Main page Press VIEW PRO OSB 3
Front dash, MFCD DSMS Profile Control page Set release settings
Front dash, MFCD DSMS Profile Control page Press CHG SET OSB 16
Front dash, MFCD DSMS Settings page Set release settings
Control stick Master Mode Select Button Cycle to CCRP Press Master Mode Select Button
HUD HUD symbology Align reticle over ASL and hold weapon release button down. Press Weapon Release Button
Control stick Laser fire switch Turn on Laser after bomb is released Press Nosewheel Steering Button
Front dash, MFCD TGP Maintain TGP line of sight to target during bomb time of flight
IAM-Guided Bomb
Designation device Set SPI using steerpoint, TDC,
TGP, TAD or Maverick (TMS Forward Long)
Left console, AHCP Master Arm switch Set to ARM
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Control stick Master Mode Select Button Cycle to CCRP Press Master Mode Select Button
HUD HUD symbology Align reticle over ASL and hold weapon release button down. Press Weapon Release Button
Control stick HUD symbology Bomb will release when release cue is between max and min range carets on reticle.
Maverick
Left console, AHCP Master Arm switch Set to ARM
Front dash, MFCD MAV OSB Press
Front dash, MFCD MAV page Power ON Maverick, press OSB 6. 3 minute alignment
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Control stick Master Mode Select Button Cycle to CCIP Press Master Mode Select Button
HUD HUD and MAV page Slew tracking gate over target and release slew to initiate tracking Move Slew Switch
Control stick Weapon release button Press with target lock indicated by steady Pointing Cross Press Weapon release button
Gun
Left console, AHCP Master Arm switch Set to ARM
Left console, AHCP GUN/PAC switch Set to ARM
Control stick Master Mode Select Button Set mode to GUNS Press Master Mode Select Button
Left console, throttle Coolie Hat up Set HUD as SOI Press Coolie Hat Up
Control stick DMS Left or Right Short Select gunsight Press DMS Left or Right
Control stick Trigger First stage enables PAC, second stage fires gun
Rockets
Left console, AHCP Master Arm switch Set to ARM
Font dash, MFCD MFCD DSMS OSB Press
Front dash, MFCD DSMS Status page Press PROF OSB 1
Front dash, MFCD DSMS Profile Main page Press OSB 19 and 20 to select profile
Front dash, MFCD DSMS Profile Main page Press ACT PRO OSB 17
Front dash, MFCD DSMS Profile Main page Press VIEW PRO OSB 3
Front dash, MFCD DSMS Profile Control page Set release settings
Front dash, MFCD DSMS Profile Control page Press CHG SET OSB 16
Front dash, MFCD DSMS Settings page Set release settings
Control stick Master Mode Select Button Cycle to CCIP or CCRP Press Master Mode Select Button
HUD HUD symbology CCIP: align CCIP pipper over target and press and hold weapon release button.
CCRP: Align reticle over ASL and hold weapon release button down. Press Weapon Release Button